Skip to content
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
FREE SHIPPING $100+
Clipper disinfectants, 5-in-1 sprays, clipper oil and Barbicide at Primos Barber Supply

How to Clean, Oil and Disinfect Your Clippers

Clipper disinfectants, 5-in-1 sprays, clipper oil and Barbicide at Primos Barber Supply

How to Clean, Oil and Disinfect Your Clippers

Most clippers that come back to us "dead" aren't dead. They're clogged with hair, dry at the blade, and running hot because nobody oiled them for three months. A $250 clipper will outlast a bad one by years, but only if you spend ninety seconds a day on it. Here's the routine our own team runs behind the chair, and what each product in the drawer is actually for.

1 · Clean
Brush the hair out
Every single client.
Takes 10 seconds.
2 · Oil
Three drops, run it
This is the step
everyone skips.
3 · Disinfect
Between every head
Required by your
state board.

The 90-second routine between clients

1. Brush the blade out. Hair packs in behind the cutter where you can't see it. That's what makes a clipper run hot and lose power. A stiff fade brush ($9.95 for a 3-piece set) or a cheap Scalpmaster cleaning brush ($2.50) does it. Brush with the clipper off and the blade facing down so hair falls out instead of deeper in.

2. Hit it with a 5-in-1 spray. Turn the clipper on, hold it level, and spray across the blade for two or three seconds. It cleans, cools, lubricates, prevents rust and disinfects in one pass. Andis Cool Care Plus ($10.50) is the one most of our barbers buy and it's our best-selling care product by a mile. L3VEL3 5-in-1 ($8.95) and BaBylissPRO All-in-One ($9.95) do the same job.

3. Oil it. Three drops: one at each corner of the cutting blade, one in the middle. Run the clipper for five seconds, then wipe the excess with a towel. Leaving extra oil on there just collects hair.

A 5-in-1 spray is not a replacement for oil. The spray carries a light lubricant, but it evaporates. Oil is what keeps steel from grinding on steel. If you only do one of the two, oil.

Oil vs. spray: what each one is actually for

Product What it does How often Price
Clipper oil Lubricates the blade, stops heat and wear Every client $3.95–$4.95
5-in-1 / all-in-one spray Cleans, cools, disinfects, light lube, anti-rust Every client $8.95–$10.50
Blade wash / 7-in-1 Deep-cleans removed blades, flushes packed debris Weekly $10.50
Immersion disinfectant Soaks combs, shears and non-electric tools Every client $8.50
Comb & brush cleaner Strips product buildup off brushes and combs Weekly $8.95

For oil, Andis Clipper Oil ($4.95) and Wahl Professional Clipper Oil ($3.95) are both fine. Use clipper oil, not WD-40, not hair oil, not 3-in-1 household oil — those gum up and pull grit into the blade.

The weekly deep clean

Once a week, take the blade off. Everything you've been spraying past has collected under there.

  • Unscrew the blade and brush out the hair packed underneath.
  • Flush the blade with a blade wash like Andis Blade Care Plus 7-in-1 ($10.50). Run the blade in the liquid if the label says to, then let it drip dry.
  • Wipe the housing and check the screws — a loose blade screw throws your zero-gap off and chews the cutter.
  • Dry completely, reset your blade alignment, then oil before the first cut of the day.

Water is the enemy here. Never rinse a blade under the tap and reattach it wet; that's how you get rust between the teeth.

Disinfecting: what your state board expects

Clippers and trimmers are electrical, so they don't go in a jar. Use a spray disinfectant on the blade and housing between clients — a 5-in-1 covers this, or a dedicated product like Clippercide ($9.85), which disinfects and lubricates in the same can.

Combs, shears and non-electric tools are different: those get immersed. Barbicide ($8.50 for 16oz) is the standard jar on the station — mix per the label and change it out on schedule. Brushes and combs with product buildup get Ship-Shape Comb & Brush Cleaner ($8.95) once a week.

Rules vary by state and they do inspect, so follow your board's contact times and the directions on the label rather than a routine you picked up in a shop.

Running hot? It's usually one of these

  • Dry blade. The most common cause by far. Oil it and see if the heat drops.
  • Packed hair. Take the blade off and look underneath — it's probably full.
  • Bad alignment. Blades set wrong grind against each other and heat up fast.
  • Dull cutter. If it's oiled, clean and aligned and still pulling, the blade is done. Replace it; sharpening a worn cutter is throwing money at a $20 part.

A clipper that suddenly lost power usually isn't a motor problem. Clean and oil it first before assuming the worst.

What to keep on the station

The whole kit is under $35: a bottle of oil, a can of 5-in-1, a fade brush, and a Barbicide jar for your combs and shears. If you go through spray fast — most shops do — the Andis Cool Care case of 12 ($100) works out cheaper per can than buying them one at a time.

Frequently asked questions

How often should I oil my clippers?

Every client, or at minimum every day you cut. Three drops across the cutting blade, run it for five seconds, wipe the excess. It takes ten seconds and it's the single biggest factor in how long your clipper lasts.

Can I use a 5-in-1 spray instead of oil?

No. The spray cleans, cools and disinfects, and it carries a light lubricant, but it evaporates. Oil stays on the blade. Use both — spray first, then oil.

Can I put my clippers in Barbicide?

No. Never immerse an electrical tool. Barbicide is for combs, shears and other non-electric items. Clippers get a spray disinfectant on the blade and housing.

Why are my clippers pulling hair?

Usually a dry or dirty blade — clean and oil it first. If it still pulls, check your blade alignment, and if that's right, the cutter is worn and needs replacing.

What oil should I use on clipper blades?

Only clipper oil, which is a light mineral oil made for the job. Household oils, WD-40 and cooking oils gum up, attract hair and can damage the blade.

How often do I replace clipper blades?

It depends on volume. A busy barber cutting all day will get a few months out of a cutter before it stops taking hair cleanly. When a clean, oiled, properly aligned blade still pulls or skips, replace it.

Stock up on care products

Everything in this guide is in stock at Primos Barber Supply. Stop by our Federal Way storefront at The Commons, or browse online.

New to the trade or upgrading your setup? Read our guides to the best clippers for beginner barbers, the best barber trimmers in 2026, and the best foil shavers for pro barbers.

Previous article StyleCraft x 3VERSINCE Professional Trimmer: Can the ES5 Challenge Cocco Digital Gap?
Next article STMNT Grooming Goods: The Complete Buying Guide for Barbers

Leave a comment

* Required fields